diff --git a/4 VCSA/(2) VCSA/Distributed Switch Configuration.md b/4 VCSA/(2) VCSA/Distributed Switch Configuration.md new file mode 100644 index 0000000..9012b20 --- /dev/null +++ b/4 VCSA/(2) VCSA/Distributed Switch Configuration.md @@ -0,0 +1,122 @@ + +Switch Setup: +1. ![[SelectGlobe.png]] + - From the home page of VCSA in the menu on the left side, Select the globe. +2. ![[NewDistributedSwitch.png]] + - Right click "DCO Datastore" + - Hover over "Distributed Switch" + - Click "New Distributed Switch..." +3. ![[SOPs/ESXi and VCSA/VCSA/VCSA Configuration Photos/NameAndLocation.png]] + - Name: Infrastructure Distributed Switch + - Click: Next +4. ![[SelectVersion.png]] + - Select Version "7.0.3 - ESXi 7.0.3 and later" + - Click Next +5. ![[ConfigureSettings.png]] + - Number of uplinks: 4 + - Network I/O Control: Enabled + - Default port group: Not Selected + - Click Next +6. Check configuration + - Click Finish +7. Complete steps 1 through 2 again. +8. ![[ToolsNameAndLocation.png]] + - Name: Tools Distributed Switch + - Click Next +9. ![[SelectVersion 1.png]] + - Select Version "7.0.3 - ESXi 7.0.3 and later" + - Click Next +10. ![[ConfigureSettings 1.png]] + - Number of uplinks: 4 + - Network I/O Control: Enabled + - Default port group: Not Selected + - Click Next +11. Check configuration + - Click Next +Port Group Setup: +1. ![[NewDistributedPortGroup.png]] + - From the menu on the left right click "Infrastructure Distributed Switch" + - Hover over "Distributed Port Group" + - Select "New Distributed Port Group..." +2. This step will be completed for each VLAN you have except "Tools" + 1. Domain ID: 3 + 2. VCSA Management ID: 5 + 3. ESXi Management ID: 10 + 4. ESXi vMotion ID: 11 + 5. ESXi Provisioning ID: 12 + 6. Tool Web Interface ID: 25 + 7. Workstations ID: 30 + 8. Test ID: 40 + 9. Trunk ID: 666 + - ![[PortGroupNameAndLocation.png]] + - Name: <\VLAN Name\> + - Click Next + - ![[PortGroupConfigureSettings.png]] + - Port Binding: Static binding + - Port allocation: Elastic + - Number of ports: 8 + - Network resource pool: (default) + - VLAN type: VLAN + - VLAN ID: 3 + - Confirm Configuration + - Click Finish +3. Follow step 1 but on the "Tools Distributed Switch" +4. Name and Location: + - Name: Tools + - Click Next +5. Configure settings: + - Port Binding: Static Binding + - Port allocation: Elastic + - Number of ports: 8 + - Network resource pool: (default) + - VLAN type: None + - VLAN ID: 20 +6. Confirm configuration + - Click Finish +Adding Host: +1. ![[AddAndManageHosts.png]] + - In the menu on the left, right click "Infrastructure Distributed Switch" + - Click " Add and Manage Hosts..." +2. ![[Addhosts.png]] + - Select "Add hosts" + - Click Next +3. ![[Selecthosts.png]] + - Select ESXi host + - Click Next +4. ![[ManagePhysicalAdapters.png]] + - vmnic1: Uplink1 +5. Click Next +6. Click Next +7. Confirm Configuration + - Click Finish +Removing Temporary Port Groups: + +1. ![[SelectHostTab.png]] + - Click Host in the top right menu +2. ![[EditSettings.png]] + - Right Click "DC" + - Click "Edit Settings" +3. ![[ClickDomain.png]] + - Click "Domain" + - Click "Browse ..." +4. ![[SelectDistributedDomain.png]] + - Click "Domain" with "Infrastructure Distributed Switch" + - Click "OK" +5. Click "OK" +6. Complete Step 2 for "VCSA" +7. ![[SelectVCSAManagement.png]] + - Click "VCSA Management" + - Click "Browse" +8. ![[SelectDistributedVCSAMan.png]] + - Click "VCSA Management" with "Infrastructure Distributed Switch" +9. Click "OK" +Deleting Temporary Port Groups: +1. Return to ESXi (10.2.10.30) +2. ![[SelectNetworking.png]] + - In the menu on the left click "Networking" +3. ![[SelectPortGroupsToDelete.png]] + - Right Click The standard port groups: + - Domain + - VCSA Management + - VM Network + - Click "Remove" \ No newline at end of file diff --git a/4 VCSA/(2) VCSA/VCSA Configuration.md b/4 VCSA/(2) VCSA/VCSA Configuration.md new file mode 100644 index 0000000..45e2cf7 --- /dev/null +++ b/4 VCSA/(2) VCSA/VCSA Configuration.md @@ -0,0 +1,26 @@ +1. ![[NewDatacenter.png]] + - From the VCSA homepage in the menu on the left side right click "10.2.5.5" + - Click New Datacenter +2. ![[DCODatacenter.png]] + - Name: DCO Datacenter + - Click Next +3. ![[AddHost.png]] + - In the same menu right click "DCO Datacenter" + - Select "Add Host..." +4. ![[SOPs/ESXi and VCSA/VCSA/VCSA Configuration Photos/NameAndLocation.png]] + - Host name or IP address: 10.2.10.30 + - Click Next +5. ![[ConnectionSettings.png]] + - Username: root + - Password: Standard +6. Confirm Configuration: + - Click Next +7. Click Next +8. ![[LockdownMode.png]] + - Select "Disabled" + - Click Next +9. ![[VMLocation.png]] + - Select DCO Datacenter + - Click Next +10. Check Configuration + - Click Finish \ No newline at end of file diff --git a/4 VCSA/(2) VCSA/VCSA Installation.md b/4 VCSA/(2) VCSA/VCSA Installation.md new file mode 100644 index 0000000..22cc55f --- /dev/null +++ b/4 VCSA/(2) VCSA/VCSA Installation.md @@ -0,0 +1,70 @@ + +- Installation: + 1. ![[MountISO.png]] + - Navigate In file explorer on you host machine to find your VCSA Disk Image File + - right click the file + - Click mount + 2. ![[VCSAuiInstaller.png]] + - Navigate to the mounted Drive + - Select "vcsa-ui-installer" + 3. Select win32 + 4. ![[SelectInstaller.png]] + - Click "Installer" + 5. ![[SelectInstall.png]] + - Click Install + 6. ![[Next.png]] + - Click Next + 7. ![[Terms and License agreement.png]] + - Accept the Terms and License Agreement + - Click Next + 8. ![[Target.png]] + - ESXi Host: 10.2.10.30 + - HTTPS: 443 + - User name: root + - Password: Standard + - Click Next + 9. ![[VCSAsetup.png]] + - Vm name: VCSA + - Set root password: Standard + - Click Next + 10. ![[DeploymentSize.png]] + - Deployment size: Tiny + - Storage size: Default + 11. ![[DatastoreSelect.png]] + - Leave everything as it is + - Click Next + 12. ![[VCSAnetworksetup.png]] + - Network: VCSA Management + - IP version: IPv4 + - IP assignment: static + - FDQN: *blank* + - IP address: 10.2.5.10 + - Subnet mask: 255.255.255.0 + - Default gateway: 10.2.5.1 + - DNS servers: 10.2.1.5 + - Common Ports: + - HTTP: 80 + - HTTPS: 443 + - Click Next + 13. Confirm configuration from previous steps + - Click Finish + 14. Wait through loading screen, this will take several minutes + 15. ![[Stage1Complete.png]] + 1. Continue to Stage 2 by Clicking Continue + 16. Click Next + 17. ![[NTPconfig.png]] + - Time synchronization mode: Synchronize time with the NTP servers + - NTP servers: 10.2.1.5 + - SSH access: Enabled + - Click Next + 18. ![[ssoconfig.png]] + - Single Sign-On Domain name: dco.mil + - Single Sign-On password: Standard + - Click Next + 19. Unselect CEIP + - Click Next + 20. Confirm configurations made + - Click Finish + 21. Once installation is complete navigate to https://10.2.5.10 + - username: administrator@dco.mil + - password: Standard \ No newline at end of file